10 Point System Fabric Inspection Pdf

1. 10 Point System Fabric Inspection Pdf Free
2. Fabric Inspection 4 Point System

Four-Point System, a standard established under ASTM D5430 – 07(2011), is a standardized Test Methods for fabric Visually Inspecting and Grading.

Four-Point System is adopted as the base of DQC inspection system because it has received the widest acceptance in fabric inspection due to its practical, impartial, and worldwide recognized.

10 Point System Fabric Inspection Pdf Free

What is 10 point system in fabric inspection. If you want to produce high quality garments, you need high quality piece goods. When a sewing factory receives fabric from the mill, it is difficult to conduct a full 100% inspection of the fabric. 'Apparel Search recommends a minimum 10% inspection of all piece goods prior to spreading the fabric. It is recommended that a suitable fabric inspection machine that provides a. For example, a lot of 100 rolls of 100 yards each is inspected using a 4-point system. Ten rolls (10% of total) are selected for inspection. Of these 7 are found to have less than 40 points or less and 3 are found to have more than. Textile Links and Controls fabric inspection form. ELIGIBILITY CRITERA FOR THE QUALITY INSPECTOR: 1. The person must be at least Graduate. He or she must have a minimum of two year experience in the textile industry. He or she must be well versed with the 4-point fabric inspection system. He or she must be active and physically fit. Normally, 10% of the rolls that are received are evaluated based on a four-point system. This way, fabric related quality problems can be avoided before it is put into production'Four- Point. 4-POINT INSPECTION SYSTEM The 4-Point System assigns 1, 2, 3 and 4 penalty points according to the size and significance of the defect. Each roll in the sample should be inspected with points assigned according to the following criteria: 4-POINT SYSTEM DEFECT EVALUATION Points Assigned Size of Defects (Inches) (CM) 1.

In the four-point system, a maximum of four penalty points can be assessed for any single defect and no linear yard can be assessed for any single defect and no linear yard can be assessed more than four points regardless of the number of defects within that piece.

Defects in both the warp/fill and directions will be assigned points under the following criteria.
1 point – Defects up to 3″
2 points – Defects > 3″ ≤ 6″
3 points – Defects > 6″ ≤ 9″
4 points – Defects > 9″
Any defect of a continuous nature shall be assigned four points for each yard in which it occurs.

Severe defects are assigned the maximum four points for each yard in which they occur. Example: regardless of size, hole would be penalized four points.

Continuing conditions such as barre, side center side shading, roll to roll shading, narrow or irregular width, creasing and uneven finish shall be counted four points for every yard within the roll that is found to contain these conditions.

Four points shall be assigned to each yard of the inspected roll that contains this type of shading defect.

The maximum penalty for any one yard shall not be more than four points.

Individual rolls exceeding the specified point count level shall be graded as second quality. A shipment shall be failed the inspection if the shipment penalty count points exceed the specified point count level.

Any roll having a running or repeating defect through more than ten continuous yards shall be rejected regardless of point count.

No roll that contains more than four full width defects per one hundred linear yards, shall be accepted as first quality.

Any roll found to contain defects, in any increment of one hundred yards, with an average of more than one major defect per ten linear yards will be rejected.

No roll shall be accepted that contains a major defect in the first or last three yards of the rolls. A major defect is considered to be any three or four point defect.

No roll shall be accepted as first quality that exhibits a noticeable degree of lose or tightness along either or both selvedges, or ripples, puckers, folds or creases in the body of the fabric that would prevent the fabric from lying flat when being spread in a conventional manner.

Rolls with side to side, side center side, or end to end shading, must be no less than 4.0 Grey Scale rating according to the AATCC Grey Scale or meet client’s requirement.

Lean Textile Co., Limited used FABRIC INSPECTION STANDARD ( 4-Point System ) to inspect fabric according to customer requirement.Have any question,freely contact us.

Fabric Inspection 4 Point System